Technical Papers
Brentwood team members share some of their cooling tower product/performance expertise in the following published papers.

To read the paper's abstract, click on the title in the list below. From there you can link to the full paper. Please note that papers presented at Cooling Technology Institute meetings must be purchased through that organization:

TP93-07
“Simultaneous comparison of the CTI HBIK and the EPA 13A isokinetic drift test procedures”

TP06-07
"Evaporative Pre-Coolers for Air Cooled Heat Exchangers ”

TP06-11
"A Review of Eliminator Performance”

TP06-19
“Guidelines for Selecting the Proper Film Fill”

TP00-01
“Design Features and Their Affect on High Performance Fill”

“Current Fouling Problem of PVC Film Fills and Research into New Designs to Eliminate Fouling”

“Evaluation of Anti-Fouling Replacement Fills in Utility Cooling Service”

Abstract: Cooling tower drift is defined as the percent of circulating water flow that exits from the cooling tower fan stack in the form of fine water droplets and aerosols entrained in the exhaust air. For cooling tower drift tests, the CTI recommended Heated Bead Isokinetic (HBIK) procedure is the most commonly used procedure and is close to being accepted as a code by CTI, whereas regulators prefer the EPA Method 13A procedure. In theory both procedures (if properly operated, recovered and analyzed), should give the same results. This paper examines and compares the two-isokinetic methods and their proper operation, recovery and analysis so as to obtain accurate and repeatable results.

The testing services of Midwest Research Institute (MRI) were retained by Brentwood Industries, Inc. to conduct a series of 18 drift tests by using both the CTI recommended HBIK drift test procedure and the EPA Method 13A drift test procedure. The tests were conducted simultaneously using both test procedures on two types of Brentwood drift eliminators at two water loadings and several air velocities at the Ceramic Cooling Tower Company's test facility located in Fort Worth, Texas.

The drift from the test cell was determined by isokinetically sampling a representative fraction of the test cell airflow above the drift eliminators. Lithium was added to the test cell circulating water prior to starting the series of tests to serve as an analysis tracer. Inductively coupled argon plasma spectroscopy (ICP), an extremely sensitive detection technique, was then used to measure the concentration of lithium in the circulating water and in the collected drift samples. The total drift rates were calculated from the ratio of the concentration of the lithium in the sampling train to the concentration of the lithium in the circulating water.

The CTI HBIK and the EPA 13A methods of isokinetic drift collection were found to yield nearly identical results in the series of tests.

Back to top

Abstract: Evaporative precooling of air cooled heat exchangers provides the thermodynamic advantages of water cooling towers with the reduced maintenance requirements of air cooled heat exchangers. In areas where water conservation, cooling tower plume abatement, or water discharge permits are a problem, evaporative precooling of the air going to the heat exchanger can be the solution. This paper discusses the advantages of precoolers and presents some basic design considerations.

Back to top

Abstract: Drift eliminators and the technology behind them continue to evolve as drift specifications grow more stringent and tower operators strive for the best performing products available to the marketplace. As such, the choice of best product for the application becomes more critical. One important aspect of drift performance is the pressure loss characteristic of a drift eliminator and the difference between dry and wet measurements. The differences between various eliminator configurations highlight the benefits of new technology and theory applied to drift eliminators to achieve the best performance and lower pressure drop. This yields continued improvements for the tower operator.

Back to top

Abstract: For many years PVC film fills have been the most popular choice of heat transfer media for use in cooling towers. Throughout this history, design features of these fills have continued to evolve from the first cross corrugated products through vertical flow fills to today’s popular combination designs. Some of these features are not obvious to the casual observer and if not chosen correctly can adversely affect tower performance, product cost, lifespan, or ease of installation. This paper traces the history of these fill designs while providing guidelines as to the proper fill selection.

Back to top

Abstract: In the design of a high performance cooling tower fill, many design features must be considered to produce optimum performance. This paper will show laboratory test data and detail the effect on fill performance of the following items; Flute geometry (cross-corrugated, offset-tube, vertical tube), Cross-corrugated flute angle, Sheet pitch (19mm vs. 20mm vs. 17mm vs. 12mm), Microstructure (course, fine, none), Material (PVC & polypropylene), Module depth (12' layers vs. 24" layers vs. 48" layers), Tip design (Alternate tips vs. straight tips).

Back to top

Abstract: The fouling of film fills in power plant cooling towers represents a major problem in loss of performance of the cooling tower and loss of efficiency of the power plant. The results of this loss of performance is higher energy consumption to drive the fans to move air through the cooling tower in mechanical draft towers. Higher fuel consumption in plant operations or reduced peak load output and the discharge of warmer water which poses environmental concerns to our rivers and lakes.

This paper discusses the effects of fouling on cooling tower performance and the current knowledge to how this fouling may occur, industry practices of controlling cleaning and eliminating the problem using new film fill products.

Please contact Brentwood for the full paper.

Back to top

Abstract: Many utilities with power stations served by cooling towers are considering fill replacement due to deterioration of the original fill media. Often this allows an opportunity to reevaluate the unit's thermal requirements and seek improvement on return cold water temperature, increasing unit performance. In the past, this meant specifying high efficiency, PVC packing as the most costeffective path to improved thermal performance. Vendors' submittals were typically evaluated based on capital cost plus energy cost-savings due to more economical operation of the turbine/condenser allowed by the colder than originally specified return water temperature.

New to the marketplace are anti-fouling fills that by design prevent or sharply reduce foulant buildup. However, this improvement in fouling resistance is accompanied by a modest drop in thermal performance. This may be more than offset by avoiding the high cost of aggressive water treatment required to maintain the cleanliness of higher performing fills.

This paper will describe an economic evaluation using the annual cost method, that considers the difference in two repack alternatives: anti-fouling fills and standard cross-corrugated fills. Differences in project capital costs, net plant heat rate, and water treatment costs will be computed. Using station specific economics, the least costly alternative is shown to be the use of lower efficiency anti-fouling fills with an existing water treatment program as opposed to high efficiency fills with an aggressive water treatment program.

Please contact Brentwood for the full paper.

Back to top

Home | Contact | News | Basics | Products | Links | Gallery

Copyright © 2008 Brentwood Industries, Inc.